仍未爛尾 仍未放棄 1/144 RX-93 EVO NU GUNDAM 裙甲已加細節 P.4 48樓

BoAkawaii

今日冇做咩大工程, 只係改改駕駛倉下面, 改返平底部(參照KA NU), 呢部機仲有排執 :(  

BoAkawaii

回復  BoAkawaii
嘛 還是說一句
大大加油期待你的完成品!!
ThomsonTakHing 發表於 1-2-2013 08:45 PM

謝謝Ching支持~ :)

BoAkawaii

仲未爛尾, 仍未放棄, 新年冇點搞過呢部機, 呢排只係加返d細節喺裙甲裡面...

呢塊甲整咗好耐先滿意...

裡面d細節用塑膠條加上, 好似有d夾硬嚟, 不過如果上咗色再劃埋線, 問題不大, 話晒喺裡面~

屁股中間塊甲, 左右兩邊用0.1mm膠枝加厚咗, 因為原本股部有虛位~

組合後~

前裙甲上面再加細節~

裡面d細節整咗好耐, 因為裡面原本空空如也, 要用1mm膠板填平, 再用0.1mm膠板加上細節~

JJ塊甲, 喺前面同左右兩邊加大0.1mm~

側面~

股部骨架, 由於加大咗前裙甲, 骨架亦要加闊, 先將左右兩邊切斷, 然後用角棒加長2mm, 前端加厚約1mm, 因為想JJ外甲突出d~



側面兩塊裙甲~

組合股部~
  
假組照2張~

ygat2005

股部 too big :(

麻友

5知點解覺得下半身有d細,可能睇慣NU隻腳粗d~

timyin

ching，加油呀，期待你的大作

成功之前絕不放棄夢想{:1_205:}

genesicgaogaiga

The upper part is good but the lower part is a bit too llarge and legs are too long and thin.
The proportion is not correct.
Keep going, you should be able to made it perfect.

BoAkawaii

股部 too big
ygat2005 發表於 3-3-2013 10:22 AM

Yeah...I know I'm already screwed up the hip...but I can't change that, sadly...I used up all my cosmo, not enough strength... {:1_200:}

BoAkawaii

5知點解覺得下半身有d細,可能睇慣NU隻腳粗d~
麻友 發表於 3-3-2013 12:22 PM

下半身d腳係有d瘦, 不過已經拆唔開再加粗... :26:
但係我覺得實物又唔係太差 :(

BoAkawaii

ching，加油呀，期待你的大作

成功之前絕不放棄夢想
timyin 發表於 3-3-2013 12:35 PM

唔...呢隻其實係失敗作, 但係好好醜醜都要繼續做, 畢竟第一次進行咁大工程, 都搞咗3個幾月先去到呢個進度, 小弟嘅小宇宙消耗太多, 已經冇咩能量, 一隻模型拖太多好易爛尾, 不過一直都想要一隻EVO NU模型, 為咗呢個心願, 小弟唯有繼續做 :79:

ygat2005

小宇宙消耗太多, 已經冇咩能量:x

BoAkawaii

The upper part is good but the lower part is a bit too llarge and legs are too long and thin.
The p ...
genesicgaogaiga 發表於 3-3-2013 09:39 PM

Thanks for the comment~

The hip proportion is based on 1/100 VP EVO NU, although I too think the hip is a little big, after I finished the modification... :26:

I wish I could make the hip 1mm smaller, but I can't change that already... :help:


1/100 VP EVO NU

冬暖夏涼小恐龍

小宇宙消耗太多, 已經冇咩能量
放血可燃燒小宇宙{:1_199:}

懶人

樓主堅持到完成.
呢度好多人撐你!