[問題]如果halfeye玩具有零件爛左，有乜方法解救？？？[#22已補圖]

紫月葵

原帖由 mkyfk 於 23-10-2009 01:52 PM 發表
how about AA glue?
take a photo and let us see see  la.....:78: :78:

唔知呢
見樓上(遲下再補相)

今日去過超man問個黑框眼鏡兄，佢話半眼而家冇再幫人修復T^T

genesicgaogaiga

原帖由 紫月葵 於 23-10-2009 21:56 發表
唔知呢
見樓上(遲下再補相)

今日去過超man問個黑框眼鏡兄，佢話半眼而家冇再幫人修復T^T

Repairing may not be possible.
How about spare parts?

But this can only be A/V if stock is exist.

紫月葵

原帖由 genesicgaogaiga 於 24-10-2009 11:42 AM 發表


Repairing may not be possible.
How about spare parts?

But this can only be A/V if stock is exist.

咁佢又冇講…

hehemimi

原帖由 mm9173 於 23-10-2009 01:56 PM 發表
我就两次经验同LZ分享下，希望帮到LZ

一次是我只三一的二号机因为用力方向不当导致断裂，幸好断口没有发生形变（可能这就 ...

502??

genesicgaogaiga

原帖由 hehemimi 於 24-10-2009 14:12 發表

502??

Just same as AA.

For this kind of glue, if the part does not involve any twisting, that should be fine.
If the part has to tolerate stress or twist, you need to insert a piece of fine metallic rod into the two broken parts before sticking them together.


P.S. If the part is black, you can buy the black AA from model shop but it is very expensive.
=>>Nearly $50.

紫月葵

原帖由 genesicgaogaiga 於 24-10-2009 03:10 PM 發表


Just same as AA.

For this kind of glue, if the part does not involve any twisting, that should be fine.
If the part has to tolerate stress or twist, you need to insert a piece of fine metallic ...

係咁樣斷法，用簡單圖解就係咁：


咁樣可以點救？

mkyfk

I think that's screw was screwed in too tight..........or did you drop it down?
it is difficult to fix it for AA glue, I think you should re-built this part if halfeye cannot help to fix it.

紫月葵

原帖由 mkyfk 於 25-10-2009 12:16 AM 發表
I think that's screw was screwed in too tight..........or did you drop it down?
it is difficult to fix it for AA glue, I think you should re-built this part if halfeye cannot help to fix it.

re-built?how?

genesicgaogaiga

you will need to do a copy of this part by yourself.

resin & mold

紫月葵

原帖由 genesicgaogaiga 於 25-10-2009 01:54 AM 發表
you will need to do a copy of this part by yourself.

resin & mold

is there any shop provide these kind of services?

mkyfk

I don't know, but I think it would expensive if you out source to do this.
or you can buy some plastic plate to rebuilt it, you can see japan hobby for your reference, they always rebuilt by themselves.:74:

Sure! it is a big project and not easily.......:! :!

hehemimi

原帖由 紫月葵 於 25-10-2009 02:41 AM 發表
is there any shop provide these kind of services?

yaxoo拍賣上有一間賣"halfeye rebuilt 神魂合體"既hobby shop...您可以係佢拍賣回應度問問....


P.S. :死圖..可否用flickr post相望望損壞情況....

[ 本帖最後由 hehemimi 於 28-10-2009 05:44 PM 編輯 ]

紫月葵

原帖由 hehemimi 於 28-10-2009 08:26 AM 發表


yaxoo拍賣上有一間賣"halfeye rebuilt 神魂合體"既hobby shop...您可以係佢拍賣回應度問問....

搵唔到既？可以pm條link比我嘛？=]