ZIN 發表於 23-10-2011 12:19:36

我前後兩對翼都無樹:35:(撩砌:68:)

alexakf 發表於 23-10-2011 12:36:28

See my post
christse2 發表於 22-10-2011 12:38 PM http://www.toysdaily.com/discuz/images/common/back.gif

我就無直入鐵支..我只用AA膠都ok..我仲係螺絲位加雪油(玩具四驅車雪油,):71:

高機動型黑百合 發表於 23-10-2011 17:50:27

See my post
christse2 發表於 22-10-2011 12:38 PM http://toysdaily.com/discuz/images/common/back.gif



借圖一用:64:
http://blog.yimg.com/3/nwqY9m17s59MX_QKyKiRCV8MzL9JtMYvhNs6.gNIW1XyW1nY_nA.Cw--/45/l/v5bpjeJXJ9AviJvToT1Gyg.jpg

我爛右, 你爛左.:42:
我只用AA膠, 無用銅枝.
因為無"架生":56:
痴完成個較位都茶左好多雪油.
上縲絲時已好輕手,
現在鬆緊剛剛好, 轉得幾順.:64:

師兄, 我想問下圖用來姐住縲絲個個蓋, 點鬆出來?
我想鬆第二個較位出來加雪油. 加左順好多.
我拿"他筆"整不到出來.
指教下. thx:64:

http://blog.yimg.com/3/nwqY9m17s59MX_QKyKiRCV8MzL9JtMYvhNs6.gNIW1XyW1nY_nA.Cw--/29/l/VX7cNC9PH7BulqVeK.020w.jpg

高機動型黑百合 發表於 23-10-2011 17:52:14

我就無直入鐵支..我只用AA膠都ok..我仲係螺絲位加雪油(玩具四驅車雪油,)
alexakf 發表於 23-10-2011 12:36 PM http://toysdaily.com/discuz/images/common/back.gif


我都係螺絲位加左勁多雪油...
必哂出來...:38:
加左雪油順哂...:51:

高機動型黑百合 發表於 23-10-2011 17:54:01

我前後兩對翼都無樹(撩砌)
ZIN 發表於 23-10-2011 12:19 PM http://toysdaily.com/discuz/images/common/back.gif


   
爛係遲早...:38:
跟本d材料同design有問題.:blame:
上縲絲太緊又不得.:80:

christse2 發表於 23-10-2011 22:05:33

回復 18# 高機動型黑百合

我只救爛果個關節，修理期間見原本個蓋就只用AA膠黏。如夾硬撬會整爛，D膠咁弱。

高機動型黑百合 發表於 23-10-2011 22:23:35

回復高機動型黑百合

我只救爛果個關節，修理期間見原本個蓋就只用AA膠黏。如夾硬撬會整爛，D膠咁弱。
christse2 發表於 23-10-2011 10:05 PM http://www.toysdaily.com/discuz/images/common/back.gif



咁你修理左另一個較未?:64:

ChefKira 發表於 25-10-2011 11:40:21

I fixed the join that links 3 pieces of the wing together on one of the wings last nite.This join had the internal spacer broken out.

The procedure:
1) take the join apart and remove the cap that covers the screw
2) unscrew the screw
3) super glue the spacer back to its original position, make sure it is glued and cured completely
4) drop some glue on the surface of the broken area to fill the crack
5) let it sit over night
6) after it is completely cured, use a very fine sanding paper to sand out any glue residue
7) also sand down the entire spacer to a little bit to make it less friction against the rubber joining inside.DON'T over sand it, just a little bit would be fine
8) use silicone oil and put couple drops inside the entire join
9) reassemble the join and put the screw back on and tighten it
10) DO NOT over tighten the screw and make sure the wing can spread easily
11) adjust the tightness of the screw if the wing spread is too loose or too tight

I'm still fixing the other join on the same wing.Will share the procedure once it is done.
頁: 1 [2]
查看完整版本: 有無人識痴EX真三一對翼?