我剛剛買番黎:50: 原帖由 zzzdx 於 18-11-2009 01:27 PM 發表 http://www.toysdaily.com/discuz/images/common/back.gif
沒有嗎?看這個我以為有的說...
http://livedoor.blogimg.jp/hacchaka/imgs/b/a/ba44c63f-s.jpg
白色哪不是的:(:(:( 原帖由 quentinlau 於 18-11-2009 02:38 AM 發表 http://www.toysdaily.com/discuz/images/common/back.gif
大大有冇圖?
+ 我的鏈接有冇幫助? 雖然我不懂輸入中文，但如果你不懂英文就請告訴我
我看得慬,:(:(:(
我只是英文不太好:unhappy::unhappy::unhappy:
同埋用aa膠搞完之後會唔會動不了@@? 原帖由 carton1216 於 18-11-2009 09:56 PM 發表 http://www.toysdaily.com/discuz/images/common/back.gif
咪嚇我
我剛剛買番黎:50:
大大小心d玩lo~
:o:o:o http://i995.photobucket.com/albums/af76/chengkt1991/SDC11278.jpg
原本archer的假關節:(:(:(
http://i995.photobucket.com/albums/af76/chengkt1991/SDC11279.jpg:Q:Q:Q
http://i995.photobucket.com/albums/af76/chengkt1991/SDC11280.jpg?t=1258557190:time::time::time: 看圖...應該是冇得救的了, 用aa膠搞完之後都是動不了的...
ps. 小弟買的figma都有10多只了, 亦會不時拿上手把玩, 但都未曾玩爛過關節
以小弟的經驗看來, figma的關節強度是ok的, 易唔易爛真是好depend on 個人的玩法...
當然關節強度是不及山口式的...如以玩山口那種左拗右擰的方法玩figma是死硬的...記得figma之前都有提過它的關節的活動原理和方式, 小心點應該是不易玩爛的... Other than superglue, epoxy putty is another solution that I hear from time to time. It *can* be fixed either way - i..e don't give up!
Figma sometimes suffer QC problem - I know some tend to break easily. Tsukasa (柊司/柊 つかさ) and Drossel are some of the examples for shoulder joints.
Otherwise, it may come down to handling problem. As hoying710大大 has mentioned, they're not as durable as 山口式. Joints must be handled carefully and held near the joints. 我絕望了............
:unhappy: :unhappy: :unhappy:
回覆 22# 的文章
"epoxy putty"@@?! ....應該仲有一救的機會.但你需要一支1~1.5MM之間的鑽咀,一條乎合鑽咀直徑的硬身鐵線,一些混合畢地,AA膠,加起來應該仲救得到.當然仲再一D技巧. 原帖由 D-E-V-I-L 於 19-11-2009 10:40 PM 發表 http://www.toysdaily.com/discuz/images/common/back.gif
買過隻把啦
好貴Orz.............
:Q:Q:Q 原帖由 warxv 於 19-11-2009 11:34 PM 發表 http://www.toysdaily.com/discuz/images/common/back.gif
....應該仲有一救的機會.但你需要一支1~1.5MM之間的鑽咀,一條乎合鑽咀直徑的硬身鐵線,一些混合畢地,AA膠,加起來應該仲救得到.
當然仲再一D技巧.
聽起來有點深奧:?:?:?
但總算有希望:handshake::handshake::handshake: ~~~關節接駁篇~~~一直都沒有機會介紹怎樣接駁斷左的關節,今次沒什麼說就說一說.http://f20.yahoofs.com/hkblog/0dwaMIaFEQWVVra9wQ--_26/blog/ap_20080831031405149.jpg.jpg?ib_____DoMbKCPuQ用風筒加熱斷了的地方嘗試將[管柱]起出來,這樣會比較慳功夫.http://f20.yahoofs.com/hkblog/0dwaMIaFEQWVVra9wQ--_26/blog/ap_20080831031429407.jpg.jpg?ib_____DBWTWbHsL一般情況只要用AA膠黐實其實也已經可以,不過如果遇上比例受力的位置就要再加功了.http://f20.yahoofs.com/hkblog/0dwaMIaFEQWVVra9wQ--_26/blog/ap_20080831032130325.jpg.jpg?ib_____DQl669VNJ
將管柱及關節鑽一個孔貫通,之後加上銅枝(看情況有時可能上鋼枝),再用AA膠黐實就可以很好的牢固度.http://f20.yahoofs.com/hkblog/0dwaMIaFEQWVVra9wQ--_26/blog/ap_20080831032152334.jpg.jpg?ib_____D13CoD2g9最後如果遇上很受力的地方就要嘗試在斷的位置外圍加上混合畢地了,圖中是未完成的,因為要等畢地乾了之後用刀修整一下,削去影響活動的地方.
回覆 24# 的文章
I think epoxy = 環氧樹脂. 混合畢地 works fine too by the way.What warxv bigbig showed is called pinning as I've mentioned on my first post (first URL link). You should give it a try. It's one of the best and most stable method to fix joints.
[ 本帖最後由 quentinlau 於 20-11-2009 03:02 AM 編輯 ]