上色之前要準備d咩

aesopa09843

唔好意思,請問一下上色之前要準備d咩?係唔係要把每件模型件都用沙只打磨過先好上色?(好似話新模型唔磨走表面果層油難上色),如果用噴罐好唔好?

同埋想問一下呢隻油洗5洗開水?

ygat2005

cutting mat / newspaper to protect your desk
many many clamp cum stand to hold the parts after paint
打磨? 難上色? you want to paint model kit or resin kit?
噴罐 is expensive, and difficult to control
these need thinner, code: X-20/X-20A
at least have 3 size (small, middle, big) of brush
extra/cheap thinner to clean the brushes

if you want to paint the model,
i suggest you putty all the the gap first,
and prepare an extra box of model / use old stuff to practice, if you are rookie...

aesopa09843

回復 2# ygat2005


    我係呢隻罐同埋呢隻tinner  (tinner係用泥洗走d色?)


我係想砌完就咁用噴罐上色

ygat2005

砌完就咁用噴罐上色 will make the gaps much more clear{:1_203:}

X-20A is for Acrylic(water-base) Paint
X-20 is for Enamel Paint


thinner is to 稀釋 the paint, can't 洗走d色{:1_232:}



it seems you bought the Acrylic Paint...
nevermind, try and you will learn/know the skill:^

Kelvinkan

最簡單.打磨水口 上灰  上灰後等佢乾
乾左靚仔哂
上色。

aesopa09843

回復 5# Kelvinkan


   應該買咩野上灰(雙星有冇),我連d灰叫咩我都唔知唔識買:49:  師兄有冇圖可以參考一下? 咁我上左灰我諗我用手油上去算

aesopa09843

回復 4# ygat2005
喔....:oh:

goahead

回復 6# aesopa09843

如果你打算手油, 我唔建議上灰, 因為油好多層都未必會遮蓋到個底灰.

只要零件表面清潔, 無油漬等等, 已經可以開始手油, 如果初初玩上色, 唔好諗住轉顏色住. 白色件油返白色, 紅色件油返紅色等等.

水性油用返水性開油水(X-20A), 手油我自己就 1:1 咁上下, 薄薄地咁油, 一層油完等乾o左先好油第二層. 千祁唔好心急~

慢慢來~~ {:2_262:}

ygat2005

but sprayed the surfacer would make the parts easy to paint,

my proportion is 3 paint :1 thinner...

aesopa09843

回復 8# goahead


   恩謝謝:$   不過稀釋,意思係咪將枝thinner倒落罐油到搞混就係?還是倒d油出泥倒少少thinner搞混?

goahead

回復 10# aesopa09843

倒出o黎開比較好, 大約係 一份油 開 一份開油水, 如果覺得濃稠度不太好時, 逐D調節, 咁就唔會o徙油~

aesopa09843

回復 11# goahead


    唔該晒你呀:$